Endless Pools Pools Spécifications télécharger pdf (Page 26)

The Quick Reference Card provides a quick

overview of your spa’s main functions and

the operations accessible with your digital

control pad.

Spa Functions

Troubleshooting

ey 1 Light key Up key Down Key

mart winter mode

indicator

et Pump

indicator

ight

indicator

ilter

indicator

eat

indicator

et Point

indicator

Key 1

Press Key 1 key once to turn the optional jet

pump on. Press it again time to turn jets off.

A built-in timer automatically turns pump

off after 20 minutes, unless pump has been

manually deactivated first.

The “Pump 1” indicator lights up

when Pump 1 is on.

Light Key

Press Light key to turn light on. Press a sec-

ond time to turn light off. A built-in timer

automatically turns light off after 2 hours,

unless it has been manually deactivated first.

The “Light” indicator lights up when

light is on.

Up/Down Keys

Use Up or Down key to set desired water

temperature. The temperature setting will be

displayed for 5 seconds to confirm your

new selection.

The “Set Point” icon indicates that the

display shows the desired temperature,

NOT the current water temperature!

Off Mode

This mode allows you to stop all outputs for

30 minutes to perform a quick spa mainte-

nance.

Press and hold Key 1 key for 5 secs to activate

the Off mode. Quick press Key 1 key to

reactivate the system before the expiration

of the 30-minute delay.

While the Off mode is engaged, the display

will toggle between OFF and the water

temperature.

AOH

FLO

UPL

OFF

An internal hardware error has been

detected in in.xe. Contact Customer

Service.

The system has shut the heater down

because the temperature at the heater

has reached 119°F (48°C). Do not

enter the water! Remove the spa cover

and allow the water to cool down,

then shut power off and power your

spa up again to reset the system.

AOH

Temperature inside the spa skirt is too

high, causing the internal temperature

in the in.xe to increase above normal

limits. Open skirt and wait until error

clears.

FLO

The system does not detect any water

flow while the primary pump is run-

ning. Check and open water valves.

Check for water level. Clean filter. If

the problem persists, call Customer

Service.

Prr

A problem is detected with the tem-

perature probe.Call Customer Service.

The water temperature in the spa has

reached 108°F (42°C). Do not enter

the water! Remove the spa cover and

allow the water to cool down to a

lower temperature. Call Customer

Service if problem persists.

UPL

No low level configuration software has

been installed into the system. Call

Customer Service.

Water temperature Smart Winter Mode

In a heating cycle, the system first generates water flow through

the heater housing and the plumbing, in order to ensure accurate

water temperature readings as well as avoiding heater activation

in dry conditions.

After verifying pump activation and taking a water temperature

reading if required, the system automatically turns the heater on

to reach and maintain water temperature at Set Point.

The “Heater” indicator lights up when the heater is on.

It flashes when there is a request for more heat but the

heater has not yet started.

Our Smart Winter Mode protects your system from the cold by

turning pumps on several times a day to prevent water from

freezing in pipes.

The “Smart Winter Mode” indicator lights up when the Smart

Winter Mode is on.

Purge Cycles

The system is programmed to automatically turn on the option-

al jet pump 4 times daily, for 60 seconds, in order to purge the

plumbing lines and keep plumbing lines filtered clean.

8. Keypad Functions and Troubleshooting

1 2 ... 21 22 23 24 25 26 27 28

Commentaires sur ces manuels

Pas de commentaire

Endless Pools Pools Spécifications Page 26

Commentaires sur ces manuels

Produits connexes et manuels pour Piscines hors sol Endless Pools Pools